C60 Steel Suppliers in China - High Carbon AISI 1060 Factory for Engineering Applications
C60 steel is an unalloyed medium carbon engineering steel which has 0.57%-0.65% Carbon as per EN10083 standard. It has characteristics similar to that of C55 carbon steel which has high hardness and high strength after hardening. C60 is difficult to weld, and machinability is poor due to high carbon content. This steel is generally supplied in an untreated or normalized condition.
| Mat. No. | DIN | EN | AISI |
|---|---|---|---|
| 1.0601 | C60 | - | 1060 |
| C | Si | Mn | Cr | Mo | Ni | V | W | Others |
|---|---|---|---|---|---|---|---|---|
| 0.61 | max. 0.40 | 0.75 | max. 0.40 | max. 0.10 | max. 0.40 | - | - | (Cr+Mo+Ni)= max. 0.63 |
C60 is one of the higher carbon contents (0.60%) steels. It is more difficult to fabricate than the lower carbon grades.
Applications include hand tools such as screwdrivers, pliers and similar items.
- Modulus of elasticity [103 x N/mm2]: 210
- Density [g/cm3]: 7.85
- Thermal conductivity [W/m.K]: 46.6
- Electric resistivity [Ohm mm2/m]: 0.127
- Specific heat capacity [J/g.K]: 0.46
- Coefficient of Linear Thermal Expansion 10-6 °C-1: See table below
| 20-100°C | 20-200°C | 20-300°C | 20-40°C | 20-500°C |
|---|---|---|---|---|
| 11.1 | 12.1 | 12.9 | 13.5 | 13.9 |
Heat to 680-710°C, cool slowly in furnace. This will produce a maximum Brinell hardness of 241.
Normalizing temperature: 820-86°C/air.
Harden from a temperature of 800-840°C followed by water or oil quenching.
Tempering temperature: 550-660°C/air.
| Diameter (mm) | 0.2 % proof stress (N/mm²) | Tensile strength (N/mm²) | Elongation A5 (%) | Reduction Z (%) |
|---|---|---|---|---|
| up to 16 | 570 | 830-980 | 11 | 20 |
| 17-40 | 490 | 780-930 | 13 | 30 |
| 41-100 | 450 | 740-890 | 14 | 35 |
| Diameter (mm) | 0.2 % proof stress (N/mm²) | Tensile strength (N/mm²) | Elongation A5 (%) |
|---|---|---|---|
| up to 16 | min. 380 | min. 710 | min. 10 |
| 17-100 | min. 340 | min. 670 | min. 11 |
| 101-250 | min. 310 | min. 650 | min. 11 |
Hot forming temperature: 1100-800°C.
Machinability of C60 and all of the higher carbon steels is relatively poor. C60 rates at 55 to 60 % that of the AISI 1112 steel which is considered 100% machinable.
This steel is not corrosion resistant. It will rust unless protected.
C60 may be welded by all of the conventional methods. However both pre-heat and post-heat should be used when welding by an approved procedure. Pre-heat at 260 to 320°C and post-heat at 650 to 780°C.
Cold working is difficult even in the annealed condition although it may be done by conventional methods but requires greater force than the lower carbon steels.
A1: C60 steel is an unalloyed medium carbon engineering steel defined by the EN10083 standard, containing a carbon content range of 0.57% to 0.65%.
A2: C60 steel is commonly used for manufacturing hand tools, such as screwdrivers, pliers, and similar items.
A3: The machinability of C60 steel is relatively poor due to its high carbon content. It rates at 55% to 60% compared to AISI 1112 steel, which is considered 100% machinable.
A4: While C60 can be welded by all conventional methods, it requires an approved procedure utilizing both pre-heating (at 260 to 320°C) and post-heating (at 650 to 780°C).
A5: For soft annealing, C60 steel should be heated to 680-710°C and then cooled slowly in the furnace. This process yields a maximum Brinell hardness of 241.
A6: No, C60 steel is not corrosion resistant and will rust unless it is properly protected.